cringovic / dts.dts

/* * Copyright (C) 2015 Chen-Yu Tsai <wens@csie.org> * * This file is dual-licensed: you can use it either under the terms * of the GPL or the X11 license, at your option. Note that this dual * licensing only applies to this file, and not this project as a * whole. * * a) This file is free software; you can redistribute it and/or * modify it under the terms of the GNU General Public License as * published by the Free Software Foundation; either version 2 of the * License, or (at your option) any later version. * * This file is distributed in the hope that it will be useful, * but WITHOUT ANY WARRANTY; without even the implied warranty of * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the * GNU General Public License for more details. * * Or, alternatively, * * b) Permission is hereby granted, free of charge, to any person * obtaining a copy of this software and associated documentation * files (the "Software"), to deal in the Software without * restriction, including without limitation the rights to use, * copy, modify, merge, publish, distribute, sublicense, and/or * sell copies of the Software, and to permit persons to whom the * Software is furnished to do so, subject to the following * conditions: * * The above copyright notice and this permission notice shall be * included in all copies or substantial portions of the Software. * * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY, * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR * OTHER DEALINGS IN THE SOFTWARE. */ /dts-v1/; #include "sun8i-h3.dtsi" #include "sunxi-common-regulators.dtsi" #include <dt-bindings/gpio/gpio.h> #include <dt-bindings/input/input.h> / { model = "Xunlong Orange Pi PC"; compatible = "xunlong,orangepi-pc", "allwinner,sun8i-h3"; aliases { ethernet0 = &emac; serial0 = &uart0; spi0 = &spi0; }; chosen { stdout-path = "serial0:115200n8"; }; connector { compatible = "hdmi-connector"; type = "a"; port { hdmi_con_in: endpoint { remote-endpoint = <&hdmi_out_con>; }; }; }; leds { compatible = "gpio-leds"; pwr_led { label = "orangepi:green:pwr"; gpios = <&r_pio 0 10 GPIO_ACTIVE_HIGH>; default-state = "on"; }; status_led { label = "orangepi:red:status"; gpios = <&pio 0 15 GPIO_ACTIVE_HIGH>; }; }; gpio-keys { compatible = "gpio-keys"; switch-4 { label = "sw4"; linux,code = <KEY_POWER>; gpios = <&r_pio 0 3 GPIO_ACTIVE_LOW>; wakeup-source; }; }; }; &codec { allwinner,audio-routing = "Line Out", "LINEOUT", "MIC1", "Mic", "Mic", "MBIAS"; status = "okay"; }; &de { status = "okay"; }; &cpu0 { cpu-supply = <&reg_vdd_cpux>; }; &ehci0 { status = "okay"; }; &ehci1 { status = "okay"; }; &ehci2 { status = "okay"; }; &ehci3 { status = "okay"; }; &emac { phy-handle = <&int_mii_phy>; phy-mode = "mii"; allwinner,leds-active-low; status = "okay"; }; &spi0 { status = "okay"; #address-cells = <1>; #size-cells = <1>; flash@0 { compatible = "jedec,spi-nor"; reg = <0>; spi-max-frequency = <10000000>; }; }; &hdmi { status = "okay"; }; &hdmi_out { hdmi_out_con: endpoint { remote-endpoint = <&hdmi_con_in>; }; }; &ir { pinctrl-names = "default"; pinctrl-0 = <&r_ir_rx_pin>; status = "okay"; }; &mmc0 { vmmc-supply = <&reg_vcc3v3>; bus-width = <4>; cd-gpios = <&pio 5 6 GPIO_ACTIVE_LOW>; /* PF6 */ status = "okay"; }; &ohci0 { status = "okay"; }; &ohci1 { status = "okay"; }; &ohci2 { status = "okay"; }; &ohci3 { status = "okay"; }; &r_i2c { status = "okay"; reg_vdd_cpux: regulator@65 { compatible = "silergy,sy8106a"; reg = <0x65>; regulator-name = "vdd-cpux"; silergy,fixed-microvolt = <1200000>; /* * The datasheet uses 1.1V as the minimum value of VDD-CPUX, * however both the Armbian DVFS table and the official one * have operating points with voltage under 1.1V, and both * DVFS table are known to work properly at the lowest * operating point. * * Use 1.0V as the minimum voltage instead. */ regulator-min-microvolt = <1000000>; regulator-max-microvolt = <1300000>; regulator-boot-on; regulator-always-on; }; }; &reg_usb0_vbus { gpio = <&r_pio 0 2 GPIO_ACTIVE_HIGH>; /* PL2 */ status = "okay"; }; &uart0 { pinctrl-names = "default"; pinctrl-0 = <&uart0_pa_pins>; status = "okay"; }; &uart1 { pinctrl-names = "default"; pinctrl-0 = <&uart1_pins>; status = "disabled"; }; &uart2 { pinctrl-names = "default"; pinctrl-0 = <&uart2_pins>; status = "disabled"; }; &uart3 { pinctrl-names = "default"; pinctrl-0 = <&uart3_pins>; status = "disabled"; }; &usb_otg { dr_mode = "otg"; status = "okay"; }; &usbphy { usb0_id_det-gpios = <&pio 6 12 GPIO_ACTIVE_HIGH>; /* PG12 */ usb0_vbus-supply = <&reg_usb0_vbus>; /* VBUS on USB host ports are always on */ status = "okay"; };